Overview
The RU-ADA8D is an eight channel stereo audio distribution amplifier with input and output gain adjustments and input level metering. The module may be operated in mono to provide up to sixteen distributed mono signals. The inputs and outputs are connected on rear-panel detachable terminal blocks.
Each of the two line level inputs accepts either a balanced or an unbalanced signal. Each input is equipped with a front panel INPUT GAIN trimmer. Input signal levels between -14 dBV unbalanced and +9 dBu balanced may be set to the proper operating level as indicated by a dual-LED VU meter. This assures ample headroom at all normal operating levels. The maximum input level is +25 dBu.
A rear-panel switch selects between stereo and mono operation. In the mono position, input A (left) is used to drive all 16 output channels. When the module is used in a monaural system, only input A must be wired.
Audio outputs are isolated from each other and may be wired balanced or unbalanced. Each of the outputs is provided with a front panel screwdriver adjusted OUTPUT LEVEL control. Relative to a balanced +4 dBu output level, this gain potentiometer allows an adjustment range from -9 dB to +6 dB. Relative to an unbalanced -10 dBV output, each output potentiometer allows an adjustment from -3 dB to +12 dB.
The RU-ADA8D offers exceptional headroom, very low distortion, excellent crosstalk isolation, wide flat frequency response and extremely low noise with very high common-mode signal rejection. It provides exceptional audio performance for the most critical applications in a professional audio environment.
The RU-ADA8D operates from 24 Vdc connected through a rear-panel detachable terminal block.
Features:
- Stereo Audio Distribution with 8 Outputs
- Mono Audio Distribution with 16 Outputs
- Front-Panel Input Level Trimmers
- Dual-LED VU Meter for Each Input Channel
- Front-Panel Output Level Trimmers
- Inputs and Outputs on Rear Panel Detachable Terminal Blocks
- Exceptional Audio Quality for the Most Demanding Applications
Specifications
Inputs (2):
Stereo (A/left and B/right) on detachable terminal block
Input Impedance:
20 kΩ balanced or 10 kΩ unbalanced
Input Level:
+4 dBu balanced (nominal), +25 dBu maximum; -10 dBV unbalanced
Input Gain Adjustments (2):
-5 dB to +15 dB (rel. +4 dBu balanced); -3 dB to +17 dB (rel. -10 dBV unbalanced)
Input Metering (2):
Dual-LED VU Meter for Input A and Input B
Mono mode:
Rear-panel switch-selectable (input A feeds all 16 outputs)
Outputs (16):
Stereo, A (8), B (8) on detachable terminal blocks
Output Impedance:
150 Ω balanced; 75 Ω unbalanced
Output Level:
+4 dBu balanced (nominal), +24 dBu maximum; -10 dBV unbalanced
Output Level Adjustments (16):
-9 dB to +6 dB (rel. +4 dBu, balanced); -3 dB to + 12 dBu (rel. -10 dBV, unbalanced)
Frequency Response:
10 Hz to 165 kHz (+/- 0.25 dB); 10 Hz to 35 kHz (+/- 0.01 dB)
THD+N:
< 0.0025% (20 Hz to 20 kHz)
Headroom:
> 20 dB (above +4 dBu input or output)
Noise:
< -92 dB (below +4 dBu output, 20 Hz to 20 kHz)
Crosstalk:
< -85 dB (20 Hz to 1 kHz); <-70 dB (1 kHz to 20 kHz)
Ambient Operating Environment:
0° C to 50° C
Power Requirement:
GROUND REFERENCED, 24 Vdc @ 140 mA (idle, nominal), 170 mA (max.)
Case dimensions:
5.75" (14.6 cm)W x 1.65" (4.18 cm)H x 3.54" (9.0 cm)D; 3.9" (9.9 cm)D with connectors
Package Type:
Cardboard Box
Package Dimensions:
6 x 6 x 2.625 in.
Shipping Weight:
1.585 lbs.
Tariff code:
8543.70.9960
RDL Three-Year Limited Warranty
Installation of these products by the Purchaser shall constitute Purchaser’s acknowledgement and acceptance of the terms and
conditions for sale and of this warranty, and shall constitute the Purchaser’s determination of the suitability of this product for the
Purchaser’s intended application. Radio Design Labs, Inc., also referred to as RDL®, warrants to the Purchaser that products
manufactured by RDL are free from defects in material and workmanship. This warranty applies to the period of three years from the date
of shipment, except for component parts or products purchased from other sources and supplied by RDL. Such component parts or
products bear only the warranty of the manufacturer thereof in effect at the time of shipment to the Purchaser. RDL will, without charge,
and after written notice has been received and acknowledged by RDL, repair an RDL product if proved to be defective according to the
usage of the trade, when such equipment is received by RDL at the location it designates with shipment costs prepaid by the Purchaser.
RDL shall not be liable for any expense whether for repairs, replacements, material, service, or otherwise, incurred by the Purchaser or
modifications made by the Purchaser to the product. No equipment shall be deemed defective if it shall fail to operate in a normal or
proper manner due to exposure to excessive moisture in the atmosphere, excessive temperature extremes, improper environmental
cleanliness, or any other environment not consistent with the principles of good engineering practice. In no event shall RDL have any
liability for consequential damage or expense directly or indirectly arising from the use of the products, or any inability to use it either
separately or in combination with other equipment or materials, or from any other cause, whether used in accordance with instructions or
not. This warranty is void if equipment is altered in any way by other than RDL. RDL products are NOT intended for use in life support
appliances, devices, or systems. Use of RDL products in such applications is done solely at the liability of the reseller/installer and/or end
user. RDL reserves the right to change design parameters and specifications at any time without notice. The performance measurements
reflect the products at the time of printing. This warranty is in lieu of all others, either expressed or implied. No representative is authorized
to assume for RDL any other liability in connection with RDL products.
