Barix Annuncicom 155 Ruggedized IP Paging, Intercom & VoIP

Barix Annuncicom 155 Ruggedized IP Paging, Intercom & VoIP

MSRP: $870.00
Write a Review
SKU:
BAR-ANNUNCICOM155
Availability:
Ships from Manufacturer, Contact us for Pricing and Availability
Type:
Intercom & Paging

Overview

With an amplified output suitable to drive 5W into an overhead paging or panel speaker, a sensitive microphone input, selector/contact closure inputs and control output the device is equally suitable for paging, intercom, help point and monitoring applications.

A built-in switch provides two 10/100Mbps network interfaces allowing the daisy chaining of devices.


The supported codecs (PCM/uLaw/aLaw/MP3) and range of sample rates (8..48kHz) allow the optimization of the audio quality for the several applications, even in higher quality.


The Annuncicom 155, the device can operate as a streaming receiver for background music with priority messaging, as a paging or inter- com device within a Paging/Intercom system or as a digital message repeater. With the Barix SIP firmware, the device can operate as part of an IP telephony solution, for example, as an intercom panel in parking barriers, toll gates, as a SOS help point, call box etc.


Being fully EN50155 and GL “Brücke” com- pliant, the device fulfills the stringent requirements to be used in trains, cars, ships and industrial as well as outdoor installations, it is designed for harsh environments (IP65).

Applications

• Generic VoIP Intercom and Paging Device with speaker amplifier
• Voice Evacuation Systems
• Microphone Encoder for IP Audio
• Surveillance
• Help Point/SOS call box device
• Live IP Audio Encoder for Streaming Applications
• SIP and IP Paging Zone device
• LIP65 rating, tested to EN50155, suitable for applications in rolling stock

 

Features

• MP3, G.711, PCM Encoding and Decoding
• Audio Level Supervision with SNMP Trap generation
• IP Streaming via TCP, UDP, RTP, Multicast
• Microphone Input
• Line Level Output
• Amplified Output 5W (8Ohm)
• Contact Closure Input (2)
• Current sourcing LED Output (1)
• RS-485 Serial Port (1)
• Dual Ethernet
• Supervised Speaker/Mic and Control Interface
• IP65 rated, EN50155: Railway applications - Electronic equipment used on rolling stock
• Temperature range (-40..+70‘C)
• Supply Voltage (24 to 48 VDC ± 30%, <60 V)

* depends on used codec, best results @48kHz PCM

 

Specifications

ELECTRICAL

  • 24 to 48 VDC ± 30%, <60 V, 14 Watt max.
  • M12 "A" connector (male)

ETHERNET

  • 2x 10/100Mbps auto, MDI/MDI-X, Link & Activity LEDs
  • per interface, Internal switch, Protocols: TCP/IP, UDP, RTP, SIP, DHCP
  • M12 "D" connector (female)

RS-485

  • 300..230'400 Baud asynchronous, 7/8 bit
  • +12V, 100mA, fused supply output to external devices
  • M12 "A" connector (female)

LINE OUT

  • max. 11 dBm @ 600 Ohm, max. 12 dBu (FS), unloaded
  • Output impedance 40..45 Ohm, 14 mWatt max
  • Values @ 600 Ohm: Freq. response 20 Hz .. 20 kHz(-3DB)
  • Dynamic range 80dB, SNR -80dB, THD <0.15% (-3dBFS)*
  • Output level software controllable

SPEAKER OUT

  • 5.0 Watt RMS max @ 8 Ohm
  • Values @ 8 Ohm: Freq. response 10 Hz .. 15 kHz (-3dB),
  • Dynamic range 82dB, SNR -82dB, THD <0.1% (-3dBFS)*
  • Output level software controllable

MICROPHONE IN

  • Electret mic, supervised bias power (2.4..4 VDC)
  • Frequency response 50Hz ..20kHz (-3dB)*
  • Dynamic range 70dB, SNR -70dB, THD <0.05% (-3dBFS)*
  • input sensitivity software controllable

AUDIO FORMATS

  • MP3, encoding/decoding up to 192/320kbps
  • PCM 16bit @8, 16, 22.05, 24, 32, 44.1, 48 kHz
  • G.711, uLaw, aLaw (sample rates same as PCM)

DISCRETE I/O

  • 2 fully supervised inputs
  • 1 LED driver output, current limited
  • internal temperature sensor
  • 2 status LEDs (red/green)

PANEL INTERFACE

  • Sub-D 15 connector, all audio and I/O signals

MECHANICAL

  • Aluminum case, 460 g, with mounting wings

MIN. MOUNTING SPACE INCL. PLUGS (W X D X H)

  • 230 x 138 x 47 mm (9 x 5.43 x 1.85 inch)

DIMENSIONS (W X D X H)

  • 130 x 108 x 38 mm (5.12 x 4.25 x 1.5 inch)

MTBF

  • Calculated acc. MIL217F at 40°C
  • Min. 80 000h at "ground mobile" environment
  • Min. 225 000h at "ground fix" environment
  • Calculated acc. IEC62380 Standard
  • Min. 110 000h at “ground; non stationary; severe”

 

* depends on used codec, best results @48kHz PCM

The warranty period for defects due to material flaws, design errors or demonstrably careless work within the framework of software development lasts for two years with regard to hardware and one year with regard to software. The warranty period begins when the delivery is dispatched by Barix (for hardware or standard software) or upon acceptance of the software by the contractual partner (for individually developed software). If the contractual partner has purchased the product for the purpose of resale, carefully stored it and not used it, the warranty period is extended by the amount of time during which the product is stored at the contractual partner's site, but by no longer than one year. The contractual partner undertakes to notify Barix in writing (along with a detailed description) immediately, and no later than within 20 days, of any hidden defects identified during the warranty period. The warranty is excluded in the case of defects which would have been identifiable during a proper inspection of the products, as specified in point 7 of these General Terms. The warranty is also excluded for defects which Barix is not responsible for, e.g. natural wear and tear, force majeure, treatment and usage by the contractual partner or third parties which is inappropriate and contrary to regulations and purpose, interventions by the contractual partner or third parties, excessive loads, unsuitable equipment, faulty maintenance or extreme environmental influences, as well as in the case of modifications made by the contractual partner to the products before reselling them to third parties. Barix does not guarantee that the products which it delivers, processes or develops can be used uninterruptedly and absolutely flawlessly. Barix undertakes to repair or replace, at its own discretion and as quickly as possible, products which are demonstrably defective during the warranty period due to the use of bad-quality materials, faulty design or poor workmanship, or which do not have the contractually guaranteed features or functions. The contractual partner must provide Barix with all the relevant information for this. Replaced parts are the property of Barix. If it transpires that Barix is not responsible for a particular defect, the product will be repaired by Barix against payment. In the event of demonstrably defective performance on the part of Barix within the framework of an individual software development, the right of rectification is explicitly reserved. In each case, Barix is liable only for direct or indirect damage which has occurred at the contractual partner's site. Liability for indirect or consequential damage, such as lost profits, third-party claims or damage caused by the contractual partner's failure to comply with contractual obligations is thus explicitly excluded. The contractual partner does not have any further rights arising out of product defects other than those explicitly mentioned above.