Overview
Broadcast Tools SS 6.1 MLR/BNC, 6×1 Passive Switcher/Router
The SS 6.1 MLR/BNC is a transparent 6×1 BNC switcher designed for N+1 installations and other applications where composite/MPX baseband, AES-3id, or other unbalanced signal switching is necessary. Switching is accomplished using mechanical latching gold contact relays, which means that the unit can route a signal in either direction and it will keep routing signal even after losing power. The SS 6.1 MLR/BNC can be controlled and monitored locally via front panel controls and/or remotely with simple opto-isolated contact closure inputs and dry contact status relay outputs, as well with multi-drop RS-232 serial commands, or TCP/UDP commands over Ethernet.
Features
• Front panel channel selection push buttons with active channel LED indicators.
• Front panel “Enable/Mute” switch can be configured to provide a safety interlock for the front panel selection push buttons, or Mute.
• Audio/signal switching via sealed mechanical latching relays utilizing 2-form-C bifurcated – crossbar silver alloy with gold overlay contacts.
• Remote control via opto-isolated inputs, TCP/UDP Ethernet, and/or the multi-drop RS-232 serial port.
• Relay outputs for remote channel status.
• BNC jacks for audio/signal I/O.
• Removable euro-block screw terminal connectors for remote control connections, except RS-232 Serial. Necessary mating plugs are supplied.
• Power-up selection of inputs to outputs, mute or last source selected. If power is lost, the last selected channel is passed to the output.
• Fully RFI proofed.
• Surge protected internal power supply, power adapter with domestic connector supplied. International power supply optional.
• Up to two units may be mounted on the optional RA-1 rack shelf. Desktop and wall mounting is also possible.
Specifications / Documents
- Inputs/Outputs: Any input level and impedance can be used. Inputs may be balanced or unbalanced. Output levels, impedance, distortion, noise, and balancing will match that of the selected input.
- Switching Method: Passive. Mechanical latching sealed relays utilizing 2-form-C bifurcated-crossbar silver alloy contacts with gold overlay.
- Logic: Flash microprocessor with non-volatile memory.
- Operation Control: Front Panel: Momentary switches.
- Remote: Optically isolated (+3.3 to 24 VDC, or +25-48 VDC via an external 3.3K ohm resistor) wet input. Default = Dry (+5 volt pullup internally sourced) Momentary or sustained. Serial: Multi-drop RS-232, 2400, 9600, 19200, 38400 8,N,1. Ethernet: RJ45 10/100, TCP or UDP socket connections.
- Status: Front Panel: LED Indicators integrated into switches.
- Remote: Six channel status relay outputs. SPST normally open, 1-amp @ 30 VDC maximum. Refer to the fractional schematic and/or text on the rear panel for connection details.
- Interfacing:
- Audio/Signal I/O: balanced BNC connectors. Unused inputs terminated with 75-ohm resistors.
- Remote control: (2) 8-position pluggable screw terminal blocks, mating connectors supplied.
- Serial: RJ-11 jack. Reversed RJ11 modular cable/female “S9” 9-pin D-Sub adapter supplied. Ethernet: RJ45, cat5 cable supplied.
- Power Requirements: 9 VDC @ >500 ma. International input voltage power supply with domestic power cord supplied.
- Operating Environment: 32°F/0°C-122°F/50°C; 0%-95% non-condensing relative humidity; 10,000ft/3048m.
- Physical Dimensions: 5.66" x 7.125” x 1.58", aluminum extrusion chassis with (4) #6-32 screw thread mounting holes for optional RA-1 rack shelf.
- Weight: 2.0 lb.
- Options: RA-1 rack shelf, holds three units (1-RU), filler panels supplied.