Overview
The Exstreamer 1xx family of products decode IP Audio streams and play out the received Audio signal to amplifiers or speakers.
Supporting a large number of protocols, encoding methods and application specific firmware, the products can be used for Broadcast, Internet Radio, as well as VoIP applications. Control and local storage interfaces are
device specific to match different use cases
• AACplus, MP3, Ogg Vorbis, G.711, PCM linear Decoding
• IP Streaming via TCP, UDP, RTP, Multicast
• Line Level Output (Stereo)
• Relay Output (Ex110 & Ex120 only)
• RS-232 Serial Port
• Power Supply (9-30 VDC, 12-24 VAC, plug included)
• IR receiver and Display built-in (Ex110 & Ex120 only)
• MicroSD or USB Flash Interface
* depends on used codec, best results @48kHz PCM
** high quality A/D supports only certain sample rates
Designed in Switzerland and installed in tens of thousands of locations worldwide, the Barix Exstreamer series is the established standard for Instore Radio, Internet Radio, Entertainment and Broadcast applications alike.
Applications
• Multiroom IP Audio System Receiver
• Instore Audio Player
• Internet Radio Receiver
• SIP and IP Paging Zone Device
• Digital Annunciator, Message Player,
• Message Repeater
• Generic VoIP decoder for IP Paging and Announcement applications
• Commercial Audio Streaming Application
Specifications
ELECTRICAL
- 9 to 30 VDC, 12 to 24 VAC, 6 Watt max.
- 2.1mm barrel connector
ETHERNET
- 10/100Mbps auto,
- RJ-45 connector with integrated Link/Activity LED
- Protocols: TCP/IP, UDP, RTP, SIP, DHCP,
ANALOG OUTPUT
- Line level output, 40..60 Ohm output impedance on RCA and 1/8" headphone jack. Output level software controllable
- Full scale output voltage: 5.6 dBu, 4 Vpp
- Frequency response (-3dB) 19Hz ..22kHz *
- Dynamic range 87 dB
- SNR/THD -87 dB, <0.05%
AUDIO FORMATS
- MP3 CBR/VBR, up to 320kbps, 8..48kHz sample freq.
- AAC, AAC plus, AAC-HE (AAC plus V2)
- WMA (up to version 9), Ogg Vorbis
- PCM 16bit @8, 16, 22.05, 24, 32, 44.1, 48 kHz
- G.711, uLaw, aLaw (sample rates same as PCM)
DISCRETE I/O
- 1 NO relay contact, 24V 0.5A (110&120 models only)
RS-232 INTERFACE
- 300..230'400 Baud asynchronous, tunneling or local control
DISPLAY
- Backlit LCD, 2x16 chars (110&120 models only)
IR INTERFACE
- IR via serial port, built-in IR receiver (110&120 models only)
- IR remote control included with Exstreamer 110 & 120
MECHANICAL
- Aluminum case, 250g, rack and wall mountable using accessories
- DIMENSIONS (W X H X D)
- 108x38x78.7mm (4.25x1.5x3.1 inch)
MODEL COMPARISON
- Model 100 Memory USB, IR use kit
- Model 105 Memory MicroSD, IR use kit
- Model 110 Display 2x16, Memory USB, Relay
- Model 120 Display 2x16, Memory MicroSD, Relay
MTBF Calculated acc. MIL217F at 25°C
- Exstreamer 100 min. 480 000h
- Exstreamer 105 min. 460 000h
- Exstreamer 110 min. 450 000h
- Exstreamer 120 min. 430 000h
* depends on used codec, best results @48kHz PCM
** high quality A/D supports only certain sample rates
The warranty period for defects due to material flaws, design errors or demonstrably careless work within the framework of software development lasts for two years with regard to hardware and one year with regard to software. The warranty period begins when the delivery is dispatched by Barix (for hardware or standard software) or upon acceptance of the software by the contractual partner (for individually developed software).
If the contractual partner has purchased the product for the purpose of resale, carefully stored it and not used it, the warranty period is extended by the amount of time during which the product is stored at the contractual partner's site, but by no longer than one year. The contractual partner undertakes to notify Barix in writing (along with a detailed description) immediately, and no later than within 20 days, of any hidden defects identified during the warranty period. The warranty is excluded in the case of defects which would have been identifiable during a proper inspection of the products, as specified in point 7 of these General Terms.
The warranty is also excluded for defects which Barix is not responsible for, e.g. natural wear and tear, force majeure, treatment and usage by the contractual partner or third parties which is inappropriate and contrary to regulations and purpose, interventions by the contractual partner or third parties, excessive loads, unsuitable equipment, faulty maintenance or extreme environmental influences, as well as in the case of modifications made by the contractual partner to the products before reselling them to third parties.
Barix does not guarantee that the products which it delivers, processes or develops can be used uninterruptedly and absolutely flawlessly.
Barix undertakes to repair or replace, at its own discretion and as quickly as possible, products which are demonstrably defective during the warranty period due to the use of bad-quality materials, faulty design or poor workmanship, or which do not have the contractually guaranteed features or functions. The contractual partner must provide Barix with all the relevant information for this. Replaced parts are the property of Barix. If it transpires that Barix is not responsible for a particular defect, the product will be repaired by Barix against payment.
In the event of demonstrably defective performance on the part of Barix within the framework of an individual software development, the right of rectification is explicitly reserved.
In each case, Barix is liable only for direct or indirect damage which has occurred at the contractual partner's site. Liability for indirect or consequential damage, such as lost profits, third-party claims or damage caused by the contractual partner's failure to comply with contractual obligations is thus explicitly excluded.
The contractual partner does not have any further rights arising out of product defects other than those explicitly mentioned above.
