Overview
The EZ-MPA2 is a stereo microphone preamplifier with front-panel volume controls and audio level metering. A front-panel switch engages audio compressors to control overloads and clipping during high level audio bursts or peaks from the microphones. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. The line output is available on RCA or MINI jacks. Left and right channel LED VU metering facilitates easy level adjustment. The EZ-MPA2 is ideal to add microphone inputs to mixers and amplifiers with line inputs. It is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms, studios and commercial sound systems.
Features:
- Left and Right Balanced XLR Microphone Inputs
- Switch-Selectable Phantom on Rear Panel
- Unbalanced Output on MINI or RCA Jacks
- Input and Output Connections on Rear Panel
- Front-Panel Compressor Enable/Disable Switch
- Audio Compressors Control Overloads
- Front-Panel LEVEL Control for Each Channel
- Dual-LED VU Meter for Each Channel
Advantages:
- Optimized for Dynamic or Condenser Mics
- Headroom Accomodates High Input Levels
- Headroom Increases with Lower Gain Settings
- Compressor Limits Clipping Over Wide Dynamic Range
Specifications
- Inputs (2):1.2 kΩ balanced on XLR jack, mic-level, -11 dBu max.
- Level controls (2):Off to 50 dB gain for each input
- Outputs (2):-10 dBV nominal on RCA jacks or Mini jack, +16 dBV max. without compression, -4 dBV max. with 20 dB compression
- Frequency Response:80 Hz to 40 kHz (±1 dB, mic input, -6 dB at 20 Hz with integral high-pass filter)
- THD+N:< 0.1% (35 Hz to 20 kHz, -50 dBu input)
- Compression :20 dB range, switch-selectable
- Crosstalk:Below noise floor (1 kHz)
- CMRR:> 55 dB (20 to 20 kHz)
- Metering:Dual-LED VU Meter for Left and Right, calibrated to -10 dBV output
- Phantom:Switch-selectable 24 V (IEC 61938: 2013)
- Noise:< -65 dB (below -10 dBV output, -50 dBu input)
- 24 Vdc power supply current:65 mA (idle), 90 mA (max.), 110 mA (max. with phantom)
- Case dimensions:5.75” (14.6 cm)W x 3” (7.6 cm)D
- Mounting size:1/3 rack width
- Package Type:Cardboard Box
- Package Dimensions:9.5 x 7 x 2.25 in.
- Shipping Weight:0.99 lbs.
RDL Three-Year Limited Warranty
Installation of these products by the Purchaser shall constitute Purchaser’s acknowledgement and acceptance of the terms and
conditions for sale and of this warranty, and shall constitute the Purchaser’s determination of the suitability of this product for the
Purchaser’s intended application. Radio Design Labs, Inc., also referred to as RDL®, warrants to the Purchaser that products
manufactured by RDL are free from defects in material and workmanship. This warranty applies to the period of three years from the date
of shipment, except for component parts or products purchased from other sources and supplied by RDL. Such component parts or
products bear only the warranty of the manufacturer thereof in effect at the time of shipment to the Purchaser. RDL will, without charge,
and after written notice has been received and acknowledged by RDL, repair an RDL product if proved to be defective according to the
usage of the trade, when such equipment is received by RDL at the location it designates with shipment costs prepaid by the Purchaser.
RDL shall not be liable for any expense whether for repairs, replacements, material, service, or otherwise, incurred by the Purchaser or
modifications made by the Purchaser to the product. No equipment shall be deemed defective if it shall fail to operate in a normal or
proper manner due to exposure to excessive moisture in the atmosphere, excessive temperature extremes, improper environmental
cleanliness, or any other environment not consistent with the principles of good engineering practice. In no event shall RDL have any
liability for consequential damage or expense directly or indirectly arising from the use of the products, or any inability to use it either
separately or in combination with other equipment or materials, or from any other cause, whether used in accordance with instructions or
not. This warranty is void if equipment is altered in any way by other than RDL. RDL products are NOT intended for use in life support
appliances, devices, or systems. Use of RDL products in such applications is done solely at the liability of the reseller/installer and/or end
user. RDL reserves the right to change design parameters and specifications at any time without notice. The performance measurements
reflect the products at the time of printing. This warranty is in lieu of all others, either expressed or implied. No representative is authorized
to assume for RDL any other liability in connection with RDL products.
