Overview
The D SERIES-TPS1A modules are single-pair audio sending modules compatible with RDL Format-A twisted pair products. These modules are designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources. The -TPS1A models mount in RDL WB-1U and WB-2U wall boxes, or in standard U.S. electrical boxes. The D-TPS1A features a white front-panel laminate with gray lettering that matches RDL Decora©-style remote controls. The DB-TPS1A features a black front-panel laminate. The DS-TPS1A is constructed of stainless steel to coordinate with RDL Decora-style stainless steel remote controls in commercial/industrial installations.
APPLICATION: The D SERIES-TPS1A modules feature an XLR microphone input. The module provides IEC 24 V phantom and accepts input signals from both dynamic and condenser microphones. The input signal is amplified using a studio-quality microphone preamplifier optimized for normal operating levels. The rear-panel GAIN switch is normally set by the installer for NORM (normal) gain. If consistently low mic levels are expected, this switch may be set to the HIGH gain position. The pre-amplified microphone source is routed to one output cable pair selected during installation using a rear-panel switch.
These modules drive only one cable pair, therefore they accept signals and power from other mic-level or line-level Format-A senders. The D SERIES-TPS1A modules have a second RJ45 jack for these input cables. Two other single-pair senders may be chained with the -TPS1A, or a single two-pair sender may be connected. If three single-pair senders are connected together, each sender must feed a different pair: A, B or C. The -TPS1A must be set to feed pair A if it is connected together with an RDL two-pair sender that feeds stereo audio on pairs B and C. The power pair and all three audio pairs are fed through both rear-panel RJ45 jacks.
The D SERIES-TPS1A may be powered directly from a 24 Vdc power supply using the rear-panel detachable terminal block. Local power connected to the module is also fed to all connected remote modules. The -TPS1A may be remotely powered through the twisted pair cable from any other module, signal distributor or RDL power inserter connected to the same twisted pair cable. Module power is indicated by a front-panel LED.
RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity, ease of installation, unsurpassed flexibility, automatic fused power, exceptional hum rejection, low noise, and low distortion provide designers and installers the optimum choice in economical twisted pair products.
Features:
- Balanced Microphone XLR Input with Phantom
- Switch-Selectable Mic Gain on Rear Panel
- Switch Selects which RJ45 Pair (A, B or C) is Fed
- Signal and Power Pair Pass-Through on RJ45 Jacks
- Remote Powering through Twisted Pair Cable
- Fused Local Power Feeds all Connected Modules
- Local Power Input on Terminal Block
- Blue LED Indicates Module is Powered
- Daisy-Chain with Single-Pair or Two-Pair Senders
- Studio-Quality Precision Active Balanced Circuitry
Specifications
Input:
1.2 kΩ Balanced with 24 Vdc phantom (IEC 61938: 2013)
Input Level:
-45 to -65 dBu Balanced; Maximum: -40 dBu (HIGH Gain), -28 dBu (NORM Gain)
Format-A Signal Pair Used:
Switch-selectable A, B, or C
Gain:
50 dB (NORM) or 63 dB (HIGH), Switch-selectable on rear panel
Format-A Input:
RJ45 (not applicable to EM-)
Output Connection:
RJ45 (Models D-, DS-); Detachable Terminal Block (Model EM-)
Frequency Response:
100 Hz to 30 kHz (± 1 dB); integral low-cut filter -10 dB @ 30 Hz
THD+N:
< 0.1% (80 Hz to 20 kHz)
Noise below +4 dBu:
< -80 dB (NORM Gain), < -70 dB (HIGH Gain)
Headroom above +4 dBu:
> 18 dB
CMRR:
> 60 dB (HIGH Gain 50 Hz to 150 Hz), > 65 dB (NORM Gain 50 Hz to 150 Hz)
Power Connections (2):
Detachable terminal block; RJ45
Ambient Operating Environment:
0° C to 50° C
Power Requirement:
24 Vdc @ 65 mA plus connected loads
Dimensions:
1.6" (4.06 cm) W; 4.11" (10.45 cm) H; 1.89" (4.8 cm) D
Mounting Box Minimum Depth:
2.4" (Models D-, DS-); 39 mm (Model EM-)
Package Type:
Cardboard Box
Package Dimensions:
3.625 x 4.625 x 2.125 in.
Shipping Weight:
0.395 lbs.
Tariff code:
8543.70.9960
RDL Three-Year Limited Warranty
Installation of these products by the Purchaser shall constitute Purchaser’s acknowledgement and acceptance of the terms and
conditions for sale and of this warranty, and shall constitute the Purchaser’s determination of the suitability of this product for the
Purchaser’s intended application. Radio Design Labs, Inc., also referred to as RDL®, warrants to the Purchaser that products
manufactured by RDL are free from defects in material and workmanship. This warranty applies to the period of three years from the date
of shipment, except for component parts or products purchased from other sources and supplied by RDL. Such component parts or
products bear only the warranty of the manufacturer thereof in effect at the time of shipment to the Purchaser. RDL will, without charge,
and after written notice has been received and acknowledged by RDL, repair an RDL product if proved to be defective according to the
usage of the trade, when such equipment is received by RDL at the location it designates with shipment costs prepaid by the Purchaser.
RDL shall not be liable for any expense whether for repairs, replacements, material, service, or otherwise, incurred by the Purchaser or
modifications made by the Purchaser to the product. No equipment shall be deemed defective if it shall fail to operate in a normal or
proper manner due to exposure to excessive moisture in the atmosphere, excessive temperature extremes, improper environmental
cleanliness, or any other environment not consistent with the principles of good engineering practice. In no event shall RDL have any
liability for consequential damage or expense directly or indirectly arising from the use of the products, or any inability to use it either
separately or in combination with other equipment or materials, or from any other cause, whether used in accordance with instructions or
not. This warranty is void if equipment is altered in any way by other than RDL. RDL products are NOT intended for use in life support
appliances, devices, or systems. Use of RDL products in such applications is done solely at the liability of the reseller/installer and/or end
user. RDL reserves the right to change design parameters and specifications at any time without notice. The performance measurements
reflect the products at the time of printing. This warranty is in lieu of all others, either expressed or implied. No representative is authorized
to assume for RDL any other liability in connection with RDL products.