RDL ST-SSR1 2x1 Line Level Audio Switch

RDL ST-SSR1 2x1 Line Level Audio Switch

MSRP: $203.41
$152.56
Write a Review
SKU:
RDL-STSSR1
Availability:
Normally Ships From Manufacturer, Contact us for Pricing and Availability

Overview

The ST-SSR1 was designed for absolute silent switching of audio signals. It supports two balanced line-level inputs and one balanced output. Each can be used unbalanced as well. The ST-SSR1 is perfect for switching between two input signals or as a silent On/Off switch for a single channel. Performance is in keeping with the technical standards for which RDL® has become known. The user can program the module for either fast or soft switching.

The SELECT input feeds the OUTPUT when the TRIG terminal is grounded, otherwise the OUTPUT is fed by the NORMAL input.

The control current required at the TRIG terminal is so minimal (< 0.5 mA) that the ST-SSR1 can be controlled from nearly any source from switches to logic circuits.

The ST-SSR1 may be controlled using the RDL D-RC2ST or the D-RT2 remote controls.

Features:

  • Switch Line Level Sources
  • Select Between Two Balanced Lines
  • Silent Audio Switching
  • Switching Without Hard Relay Contacts
  • Fast Switching for Audio Muting
  • Selection by Open-Collector Logic

Specifications

 
Inputs (2):
20 kΩ balanced, +4 dBu nominal
 
Audio Output:
+4 dBu nominal, 150 Ω balanced, terminal block
 
Switching Time:
Fast    /    Soft
 
Time required for NORMAL input to turn off:
10 us   /    5 ms
 
Time required for NORMAL input to turn on:
15 us   /    70 ms
 
Time required for SELECT input to turn off:
15 us   /    10 ms
 
Time required for SELECT input to turn on:
20 us   /    35 ms
 
Control Signal:
 
TRIG terminal must be externally
pulled to ground
 
Control Current:
0.5 mA
 
THD+N:
< 0.05%
 
Frequency Response:
15 Hz to 20 kHz (± 0.5 dB, bridging load)
30 Hz to 20 kHz (± 0.5 dB, 600 Ω load)
 
Noise (below +4 dBu):
< -80 dB (85 dB typical)
 
Headroom (above +4 dBu):
> 18 dB
 
CMRR
> 45 dB (100 Hz, either port)
 
ON Gain:
Unity (600 Ω balanced input/output)
 
OFF Attenuation:
> 80 dB (10 Hz to 20 kHz, either input)
 
Indicators (2):
LED showing active input (left LED=NORMAL; right LED=SELECT)
 
Ambient Operating Environment:
0° C to 55° C
 
Power Requirement:
GROUND-REFERENCED, 24 Vdc @ 40 mA
 
Package Type:
Cardboard Box
 
Package Dimensions:
2 x 2 x 4 in.
 
Shipping Weight:
0.198 lbs.
 

 

RDL Three-Year Limited Warranty Installation of these products by the Purchaser shall constitute Purchaser’s acknowledgement and acceptance of the terms and conditions for sale and of this warranty, and shall constitute the Purchaser’s determination of the suitability of this product for the Purchaser’s intended application. Radio Design Labs, Inc., also referred to as RDL®, warrants to the Purchaser that products manufactured by RDL are free from defects in material and workmanship. This warranty applies to the period of three years from the date of shipment, except for component parts or products purchased from other sources and supplied by RDL. Such component parts or products bear only the warranty of the manufacturer thereof in effect at the time of shipment to the Purchaser. RDL will, without charge, and after written notice has been received and acknowledged by RDL, repair an RDL product if proved to be defective according to the usage of the trade, when such equipment is received by RDL at the location it designates with shipment costs prepaid by the Purchaser. RDL shall not be liable for any expense whether for repairs, replacements, material, service, or otherwise, incurred by the Purchaser or modifications made by the Purchaser to the product. No equipment shall be deemed defective if it shall fail to operate in a normal or proper manner due to exposure to excessive moisture in the atmosphere, excessive temperature extremes, improper environmental cleanliness, or any other environment not consistent with the principles of good engineering practice. In no event shall RDL have any liability for consequential damage or expense directly or indirectly arising from the use of the products, or any inability to use it either separately or in combination with other equipment or materials, or from any other cause, whether used in accordance with instructions or not. This warranty is void if equipment is altered in any way by other than RDL. RDL products are NOT intended for use in life support appliances, devices, or systems. Use of RDL products in such applications is done solely at the liability of the reseller/installer and/or end user. RDL reserves the right to change design parameters and specifications at any time without notice. The performance measurements reflect the products at the time of printing. This warranty is in lieu of all others, either expressed or implied. No representative is authorized to assume for RDL any other liability in connection with RDL products.