Overview
AudioScience Iyo Dante 16.16M, 16 Input/Output Dante Audio Over IP Interface-Terminal Block
The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. Seven models provide various configurations of balanced analog audio inputs and outputs. Each input accommodates microphone through line level signals with a gain range of -60 to +24dBu. +48V phantom power is individually switchable on each input. Output levels are configurable up to +24dBu.
Iyo devices can be used in Dante network installations or can also be set to operate as AES67 devices for use in Livewire+™ networks.
When used in conjunction with the Audinate's Dante Virtual Soundcard (DVS) installed on your PC, all Iyo Dante units can operate as direct input/output PC devices. Or use them as stand alone input/output devices to connect to other endpoints in a larger Dante network environment.
Available Terminal Block Configurations
| Model | Audio In Channels | Audio Out Channels | Input Type | Output Type |
|---|---|---|---|---|
| Iyo Dante 8.8M | 8 | 8 | Balanced Mic/Line | Balanced Line |
| Iyo Dante 16.16M | 16 | 16 | Balanced Mic/Line | Balanced Line |
| Iyo Dante 32.32M | 32 | 32 | Balanced Mic/Line | Balanced Line |
| Iyo Dante 16.0M | 16 | 0 | Balanced Mic/Line | None |
| Iyo Dante 0.16L | 0 | 16 | None | Balanced Line |
| Iyo Dante 32.0M | 32 | 0 | Balanced Mic/Line | None |
| Iyo Dante 0.32L | 0 | 32 | None | Balanced Line |
Features
- Up to 32 channels of Dante audio-over-IP with AES67 interoperability
- 44.1, 48 or 96kHz sample rates
- Balanced microphone/line level inputs with level range of -60 to +24dBu
- Balanced line level outputs with level range of 0 to +24dBu
- Switchable +48V phantom power on each input
- RGB front panel LEDs provide per channel metering and stream status
- Built in web server provides audio level configuration and monitoring
- 1U rack-mount unit
- Dual RJ-45 network jacks can be operated in redundant or switched mode
- Built-in universal 90-260VAC power supply
- Auxiliary +12VDC input provides power supply redundancy
- Dante Domain Manager "DDM" ready
- Public control protocol
Specifications / Documents
DANTE INPUT/OUTPUT
- Type: 100/1000Mb Ethernet
- Connector: Dual RJ-45 operable as redundant Dante or as a network switch
- Channels: 16.16M – 16 input and 16 output channels
- Audio formats: 16, 24 and 32 bits per sample
- Sample Rate: 44.1kHz, 48kHz, 96kHz
- Latency: 0.15, 0.25, 0.5, 1.0 and 5.0ms
ANALOG MIC/LINE INPUT
- Type: Balanced
- Input Level: -60 to +24dBu in 1dBu steps
- EIN: -126 dBu Equivalent Input Noise @ -26dBu level setting
- Phantom Power:+48V @ 10mA per channel max , software switchable
- A/D converter: 32 bit over sampling
- Input Impedance: 10K ohms
- Dynamic Range: >114dB
- THD+N: < -97dB
- Frequency Response
- @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-3.0dB
- @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-3.0dB
- Connectors: 3.81mm Terminal Block
ANALOG LINE OUTPUT
- Type: Balanced
- Output Level: -10 to +24dBu in 1dBu steps
- D/A converter: 32 bit over sampling
- Load Impedance: 2K ohms or greater
- Dynamic Range: >114dB
- THD+N: < -100dB
- Frequency Response
- @ 48kHz Sample Rate: 20Hz to 20kHz +0.1/-0.25dB
- @ 96kHz Sample Rate: 20Hz to 40kHz +0.1/-3.0dB
- Connectors 3.81mm Terminal Block
GPIO
Opto-isolated Inputs
- Isolation: 2,500 VAC RMS
- Input Drive: 4mA typical with internal 5V supply and internal 1K current limiting resistor
- Input Voltage: Range Between 3V and 24V. Add external resistor above 24V to limit current.
Relay-isolated Outputs
- Isolation: 1,500 VAC
- Contact Rating: Up to 60 VDC/60VAC and 350mA, 600mW maximum
LATENCY (48kHz, L24)
- Analog Input to Dante Transmit: 770.21 μs
- Dante Receive to Analog Output: 713.05 μs
POWER
- Built in Power supply: 90-260VAC, 47-63Hz with IEC C-14 AC inlet
- Redundant Power supply (Optional): Supplied using an external +12VDC, 60W power supply with 2.1mm locking plug ASI part number for power supply: PWR1101
