Vorsis M2 Dual Channel Digital Mic/Voice Processor
Two Independent Voice Processing ChannelsThe M-2 is a dual-channel DSP-based voice processor which operates as two independent channels.The M-2 microphone processor is equipped with twin, matched Super-Quiet (SQ) microphone preamplifiers featuring extremely low noise floor, very wide dynamic range, faithfully accurate transient response, and ruler flat frequency response. Operating in harmony with high quality 24-bit A/D converters and a 48kHz base sample rate, the M-2 adds absolutely no undesired coloration to the signal and faithfully preserves the sound of any microphone and talent combination. It also features a four-section equalizer with high and low shelving EQ and two bands of fully parametric EQ, high and low pass filters, compressor, de-esser, expander and limiter functions.Included in the M-2 dual-channel voice processor is Wheatstone’s smooth-sounding Vorsis dynamics processing, configurable to up to three bands of processing. Adjustable from anywhere on your network, the M-2 offers the security of password protected TCP/IP-based remote control and no front panel controls.
Wheatstone-designed Dynamics Control
A high performance de-esser and a smooth sounding, very low distortion compressor/limiter dynamics control section round out the M-2’s offerings to create powerful and authoritative presence on production or on-air microphones.
Very high quality parametric and shelving equalization is available to sweeten the sound of any microphone as desired without adding noise or undesirable artifacts to the signal.
Wheatstone Processing Presets
A variety of ready-to-use factory processing presets are provided, carefully tailored for different processing goals and formats. You can select a factory preset, confident that it will sound great just as it is. Or use a factory preset as a starting point and create a custom sound for each announcer, then save the new settings as a personalized user preset. In a facility with multiple microphone processors, presets saved in one unit can be easily copied to the others.
Factory presets are pre-installed and write protected.
New factory presets can be downloaded from the Wheatstone-Processing.com web site and installed via the Windows-based GUI software.
Storage for 80 presets in on-board non-volatile memory, unlimited storage on host PC.
Microphone XLR-F connector: two
Electronic differential: >2KΩ (bridging)
Optimum source impedance: 200Ω
Phantom Power: 48VDC, switchable on/off
Gain: -10dB to +70dB in 1dB steps
Frequency response: ±0.2dB 20Hz-20KHz
Equivalent input noise (EIN): -128dBu
THD+N: <0.03%, 20Hz-20kHz, -50dBu input
SMPTE DIM: 0.00007%
Digital XLR-M connector: two,
Two RJ45 to StudioHub: standard
Reference Level: 0VU=-20dBFS
Output Sample Rates: 48kHz fixed
Balanced: 110Ω AES-3 0VU=-20dBfs
Analog XLR-M connector: Two
Electronically balanced : <10Ω source impedance
Optimum load impedance: >600Ω
Maximum output level: +24dBu
Asymmetry filter Phase rotator, 4th order allpass, switchable in/out
High-pass: 24dB/octave Butterworth
Low-pass: 24dB/octave Butterworth
Notch: Fixed bandwidth
Threshold Adjustable: -60dBFS to 0dBFS
Depth Adjustable: 0-40dB
Close Adjustable: 50ms-3s
Threshold Adjustable: -10dBFS to -60dBFS
Release time Adjustable: 50ms-500ms
De-ess frequency Adjustable: 20Hz-20kHz
Routable: Pre or post compressor
Band 1: Shelving
Bands 2 and 3: Parametric
Bandwidth: 0.2-3.0 octave
Band 4: Shelving
One, two, or three processing bands
Band 1-2: adjustable 20Hz-1kHz
Band 2-3: adjustable 1kHz-20kHz
Threshold: 10 to -50dBFS
Attack time: 0.2ms-1s
Release time: 33ms-1s
Control: Zero-overshoot look-ahead limiter
Threshold: -50 to -10dBFS
RJ45 connector: two
Optional Wheatstone Announcer Panel or custom interface Connections: ON, OFF, Cough, ON tally, OFF tally, power and ground
GPI input: DB9 connector
Eight opto-isolated ports: for external switching of presets
16”/40.6cm deep (allow 3.25”/8.25cm for rear connectors)
Shipping weight: 15lbs/6.8kg
Power Requirements: 90-260VAC, 50-60Hz, 19VA