Studio Technologies Model 5401A Dante Leader Clock

Studio Technologies Model 5401A Dante Leader Clock

The Model 5401A Dante Leader Clock provides precise timing signals for applications that utilize the Dante audio-over-IP media networking technology. The unit implements a high-performance IEEE® 1588 precision time protocol (PTP) server, compatible with the requirements of Dante and capable of simultaneously supporting the timing needs of up to hundreds of Dante-compatible devices. As expected, the Model 5401A provides the PTPv1 (IEEE 1588-2002) compatibility that's required by Dante. In addition, the unit supports PTPv2 (IEEE 1588-2008) for AES67 and ST 2110-30 applications. A word clock output provides a general-purpose timing reference for use by external devices. The Model 5401A also generates eight sine wave audio tones on Dante transmitter (output) channels which can be useful during audio and data network installation, maintenance, and operation. A sync input connection allows the Model 5401A's internal oscillator to be synchronized with a variety of timing and reference signals.

• Dedicated Leader Clock for Dante audio-over-IP, AES67, and ST 2110-30 applications
• High-performance IEEE 1588 PTP v1 and v2 servers
• Internal temperature-stabilized frequency reference
• Compatible with external word clock, video sync, and 10 MHz sources
• Precision word clock output
• Eight configurable audio tone signals
• Three Gigabit Ethernet interfaces support independent Dante and management networks
• Webpage management and USB flash drive software updating
• AC mains and 12 volts DC powering
• Lightweight enclosure, single rack-space (1U) mounting
• Applications: High-performance Leader Clock for Dante audio-over-IP applications. Also supports AES67 and ST 2110-30 applications. In addition, provides audio tones on Dante transmitter (output) channels for general-purpose use and a word clock synchronization output.

Precision Time Protocol (PTP) Support:

• PTPv1 (IEEE 1588-2002) for Dante; PTPv2 (IEEE 1588-2008) for AES67-2018 and ST 2110-30:2017

Timing Reference:

• Source: internal time base, external sync input, or via an existing Dante network, selectable

Internal Time Base:

• Type: 24.576 MHz temperature-stabilized crystal oscillator
• Initial Accuracy: 1 ppm (parts-per-million)
• Long-Term Accuracy: 1 ppm (parts-per-million) per year
• Temperature Stability: ±280 ppb (parts-per-billion), 0-50 degrees C

Sync Input:

• Compatible Sources: word clock, bi-level video, tri-level video, 10 MHz
• Termination: 50 ohms (10 MHz), 75 ohms (word clock or video), or high Z (unterminated), selectable
• Word Clock Compatibility: square wave, 5 Vpp nominal unloaded, 44.1, 48, 88.2, 96, 176.4, or 192 kHz
• Video Signal Compatibility: bi- or tri-level, 1 Vpp nominal into 75 ohm load
• 10 MHz Signal Compatibility: sine wave, 3 Vpp nominal into 50 ohm load

Word Clock Output:

• Type: square wave
• Rate: 44.1, 48, 88.2, 96, 176.4, or 192 kHz
• Source Impedance: 75 ohms
• Amplitude: 5 Vpp, unterminated; 2.5 Vpp, externally terminated with 75 ohms
• Jitter: 0.01 UI (using internal time base)

Network Audio Technology:

• Type: Dante audio-over-IP
• AES67-2018 Support: yes
• ST 2110-30:2017 Support: yes
• Dante Domain Manager™ (DDM) Support: yes
• Ethernet Interface Configuration: Switched, Redundant, Switched+Mgmt, or Redundant+Mgmt, selectable
• Clock Source: follows Model 5401A timing reference configuration
• Sample Rate: 44.1, 48, 88.2, 96, 176.4, or 192 kHz, selectable
• Bit Depth: 24
• Number of Dante Transmitter (Output) Channels: 8
• Number of Dante Transmitter Flows: 32

Audio Tone Generator:

• Type: continuous sine wave signals on Dante transmitter (output) channels
• Number of Channels: 8
• Frequency: 1 Hz to 22 kHz, individually configurable in 1-Hz steps
• Amplitude: 0 to –99 dBFS, individually configurable in 1-dB steps
• Distortion (THD+N): <0.0001% (<–121 dB), measured at 1 kHz, –1 dBFS

Network Interfaces:

• Qty: 3. Dante Primary, Dante Secondary, and Management
• Type: 1000BASE-T Gigabit Ethernet (GigE) per IEEE 802.3ab (100 Mb/s supported but not recommended for optimal performance; 10 Mb/s not supported)
• Ethernet Connection NIC Status LEDs: one link and one activity for each Ethernet interface

Connectors:

• Sync Input, Word Clock Output: 2, BNC jack (female connector), per IEC 61169-8 Annex A
• Ethernet: 3, RJ45 jack
• USB: type A receptacle (used only for updating firmware)
• DC Input: 4-pin male XLR (pin 1 negative, pin 4 positive)
• AC Mains Input: 3-blade male, IEC 320 C14-compatible (mates with C13)

Power Sources:

• AC Mains: 100 to 240 V, 50/60 Hz, 5 W maximum
• DC: 10 to 18 V, 0.5 A max: 110 uA maximum with 12 volts DC and AC mains present, 190 uA maximum with 18 volts DC and AC mains present

Dimensions (Overall):

• 19.00 inches wide (48.3 cm)
• 1.72 inches high (4.4 cm)
• 7.9 inches deep (20.1 cm)
• Weight: 3.0 pounds (1.4 kg)